Advanced
Cable Testing
SUBESTACION - MEDIDOR DE TIEMPOS DE INTERRUPTORES
CBCT - VERIFICADOR DE BOBINAS DE INTERRUPTORES
El CBCT es una fuente de Tensión Continua diseñado específicamente para verificar bobinas de cierre y apertura de Interruptores de Subestaciones. El CBCT utiliza la fuente de energía de CC de la subestación para generar electrónicamente una tensión de salida programable del 5 al 95% de la tensión de la fuente. Puede mantener una corriente de prueba de hasta 80A manteniendo una regulación de la tensión mejor al 2% durante el funcionamiento de la bobina del interruptor.
| TYPE | Programmable DC Power Supply | ||
| PHYSICAL SPECIFICATIONS | 19"W x 7"H x 15"D, (48 cm x 17 cm x 38 cm); Weight: 25 lbs (11.3 kg) | ||
| INPUT VOLTAGE | 20 - 300 Vdc, 20A fuse | ||
| OUTPUT VOLTAGE | 5% - 95% of input voltage with 2% regulation at max current (up to 80A) | ||
| OUTPUT VOLTAGE CHANNELS | One continuous and one pulse DC output | ||
| OUTPUT VOLTAGE PROTECTION | Shutdown if current exceeds 80A or if current drawing time exceeds 500 ms @ 80A | ||
| VOLT METER RANGE | Input/output meters, 0 - 300 Vdc; Accuracy: 1% of reading, ±0.2V | ||
| TIMER DISPLAY RANGE | 0.0000 - 999.999 seconds; Accuracy: 0.01%, ±0.5 ms | ||
| TIMER START INPUT | Internal (coil initiation), wet-contact input (20 - 240 Vac/dc), or dry-contact input (1 - 200 ohms) | ||
| TIMER STOP INPUT | Wet-contact (20 - 240 Vac/dc) or dry-contact (1 - 200 ohms) | ||
| DISPLAY | Back-lit LCD screen (20 characters by 4 lines); viewable in both bright sunlight and low-light levels | ||
| SAFETY | Designed to meet UL 6101A-1 and CAN/CSA C22.2 No 1010.1-92 standards | ||
| ENVIRONMENT | Operating: -10°C to 50°C (+15°F to +122°F); Storage: -30°C to70°C (-22°F to +158°F) | ||
| CABLES | Two 6-foot (#8 AWG) DC cable sets, Two 10-foot timer cable sets, One ground cable, one cable bag | ||
| OPTIONS | Transportation case | ||
| WARRANTY | One year on parts and labor |
CT-3500 - ANALIZADOR DIGITAL DE INTERRUPTOR
El CT-3500 es un medidor de tiempos de Interruptor Microprocesado de segunda generación de funcionamiento independiente. Mide el tiempo transcurrido desde el instante en que una bobina del interruptor se activa al instante de apertura o cierre de los contactos secos de un interruptor. El CT-3500 no sólo mide el tiempo de respuesta de los contactos de un interruptor sino que además puede medir Relés o equipos de conmutación que utilicen una tensión inicial de disparo (24-300 Volts de corriente continua o alterna).
| TYPE | Digital circuit-breaker timer | ||
| PHYSICAL SPECIFICATIONS | 15"W x 7"H x 13"D (38.1 cm x 17.8 cm x 33.0 cm); Weight: less than 15 lbs (6.8 kg) | ||
| INPUT POWER | 100 - 120 Vac or 200 - 240 Vac (selectable), 50/60Hz | ||
| DRY CONTACT INPUTS | 3 channels | ||
| TRIGGER INPUT VOLTAGE | Open/Close: 30 - 300 V, dc/peak ac | ||
| TEST OPERATIONS | Open, Close, Open - Close, Close - Open | ||
| TIMING RESOLUTION | ± 1/10 millisecond; Accuracy: 0.05% of reading ± 0.1ms | ||
| DISPLAY | Back-lit LCD Screen (20 characters by 4 lines); viewable in bright sunlight and low-light levels | ||
| PRINTER | Built-in 2.5-inch wide thermal printer | ||
| KEYPAD | Rugged membrane keypad (10 alpha-numeric keys, 6 function keys) | ||
| INTERNAL TEST RECORD STORAGE | Stores 128 Timing Records | ||
| COMPUTER INTERFACE | RS-232C port (19,200 baud) | ||
| PC SOFTWARE | Windows® XP/Vista-based software is included with purchase price | ||
| SAFETY | Designed to meet IEC61010 (1995), UL61010A-1, CSA-C22.2 standards | ||
| ENVIRONMENT | Operating: -10ºC to 50º C (15ºF to +122º F); Storage: -30º C to 70º C (-22ºF to +158º F) | ||
| CABLES | One 20-foot contact test lead cable, one trigger cable with extension cable, one ground cable with attaching clips, cable carrying bag, power cord | ||
| OPTIONS | Transportation case | ||
| WARRANTY | One year on parts and labor |
CT-6500 S2 - ANALIZADOR DIGITAL DE INTERRUPTOR
El CT-6500 Serie 2 es un Analizador de Interruptores de EAT de funcionamiento independiente operado por una micro-computadora. Es económico y fácil de utilizar. Está disponible en modelos de 3 contactos secos (CT-6500-3); 6 contactos secos (CT-6500-6) o 12 contactos (CT-6500-12). El CT-6500 Serie 2 analiza completamente el estado del interruptor: tiempo de contacto, desplazamiento, velocidad, Sobre-Carrera e Inserción de Contacto. El análisis del movimiento del contacto incluye: Apertura, Cierre, Apertura-Cierre, Cierre-Apertura y Apertura-Cierre-Apertura.
| TYPE | Portable circuit-breaker analyzer | ||
| PHYSICAL SPECIFICATIONS | 16"W x 11"H x 14" D (40.6 cm x 29.9 cm x 35.6 cm); Weight: less than 25 lbs (11.3 kg) | ||
| INPUT POWER | 100 - 120 Vac or 200 - 240 Vac (selectable), 50/60Hz | ||
| DRY CONTACT INPUTS | 3, 6 or 12 dry input channels (depending on model). Each channel detects main and insertion-resistor contacts | ||
| TIMING WINDOWS | 1-second, 10-seconds, or 20-seconds | ||
| TIMING RESOLUTIONS | ±50 micro-seconds @ 1-second duration, ±500 micro-seconds @ 10-second duration, ±1.0 milli-seconds @ 20-second duration | ||
| TIMING ACCURACY | 0.05% of reading ±0.05 ms @ 1-second duration | ||
| DRY-CONTACT CHANNEL PROTECTION | All contact inputs are grounded until test; input channels are protected against static discharge | ||
| DRY-CONTACT DETECTION RANGE | Closed: less than 20 ohms; Open: greater than 5,000 ohms | ||
| RESISTOR DETECTION RANGE | 50 - 5,000 ohms | ||
| TRIGGER INPUT VOLTAGE | Open/Close: 30 - 300V, DC or peak AC | ||
| VOLTAGE SENSING INPUT RANGE | V1: analog input; 0 - 255V DC or peak AC; Sensitivity ±1V; V2: voltage presence/absence detector input; 30 - 300V DC or peak AC | ||
| BREAKER OPERATIONS | Initiate Open, Close, Open- Close, Close - Open, Open - Close - Open | ||
| BREAKER INITIATE CAPACITY | 30A, 250Vac/dc max | ||
| INITIATE CURRENT READING RANGE | One, non-contact, Hall-effect sensor, 0 - 20 amp range, dc to 5Khz | ||
| TRAVEL TRANSDUCER INPUTS | 3 digital travel transducer channels; Linear range, 0.0 - 60.0 in (±0.01 in); Rotary range: 0 - 360 degrees (±0.36 degrees) | ||
| CONTACT TRAVEL POINT DIFFERENCE | Measures "slow-close" contact-point distances; results can be printed | ||
| DISPLAY | Back-lit LCD Screen (20 characters by 4 lines); viewable in bright sunlight and low-light levels | ||
| PRINTER | One year on parts and labor | ||
| INTERNAL TEST RECORD STORAGE | Stores up to 200 test records | ||
| COMPUTER INTERFACES | One RS-232C port, One USB port | ||
| PC SOFTWARE | Windows® XP/Vista-based Breaker-Analysis software is included with purchase price | ||
| SAFETY | Designed to meet UL 6101A-1 and CAN/CSA C22.2 No 1010.1-92 standards | ||
| ENVIRONMENT | Operating: -10°C to 50°C (+15°F to +122°F); Storage: -30°C to70°C (-22°F to +158°F) | ||
| OPTIONS | Transportation case (available for the CT-6500 S2 and the travel transducers) | ||
| WARRANTY | One year on parts and labor |
CT-7000 S2 - ANALIZADOR DIGITAL DE INTERRUPTOR
El CT-7000 Serie 2 es un Analizador de Interruptores de EAT de tercera generación, de funcionamiento independiente operado por una micro-computadora. Es económico y fácil de utilizar. Está disponible en modelos de 3 contactos secos (CT-6500-3); 6 contactos secos (CT-6500-6) o 12 contactos (CT-6500-12). El CT-7000 analiza completamente el estado del interruptor: tiempo de contacto, desplazamiento, velocidad, Sobre-Carrera e Inserción de Contacto.
| TYPE | Portable circuit-breaker analyzer | ||
| PHYSICAL SPECIFICATIONS | 16"W X 11"H x 14"D (40.6 cm x 29.9 cm x 35.6 cm); Weight: less than 25 lbs (11.3 kg) | ||
| INPUT POWER | 100 - 120 Vac or 200 - 240 Vac (selectable), 50/60Hz | ||
| DRY CONTACT INPUTS | 3, 6 or 12 dry-input channels (depending on model). Each channel detects main and insertion-resistor contacts | ||
| TIMING WINDOWS | 1-second, 10-seconds, or 20-seconds | ||
| TIMING RESOLUTIONS | ±50 micro-seconds @ 1-second duration, ±500 micro-seconds @ 10-second duration, ±1.0 milli-seconds @ 20-second duration | ||
| TIMING ACCURACY | 0.05% of reading ±0.05 ms @ 1-second duration | ||
| DRY-CONTACT CHANNEL PROTECTION | All contact inputs are grounded until test; input channels are protected against static discharge | ||
| DRY-CONTACT DETECTION RANGE | Closed: less than 20 ohms; Open: greater than 5,000 ohms | ||
| RESISTOR DETECTION RANGE | 50 - 5,000 ohms | ||
| TRIGGER INPUT VOLTAGE | Open/Close: 30 - 300V, DC or peak AC | ||
| VOLTAGE SENSING INPUT RANGE | V1: analog input; 0 - 255V DC or peak AC; Sensitivity ±1V; V2: voltage presence/absence detector input; 30 - 300V DC or peak AC | ||
| BREAKER OPERATIONS | Initiate Open, Close, Open- Close, Close - Open, Open - Close - Open | ||
| BREAKER INITIATE CAPACITY | 30A, 250Vac/dc max | ||
| INITIATE CURRENT READING RANGE | One, non-contact, Hall-effect sensor, 0 - 20 amp range, dc to 5Khz | ||
| TRAVEL TRANSDUCER INPUTS | 3 digital travel transducer channels; Linear range, 0.0 - 60.0 in (±0.01 in); Rotary range: 0 - 360 degrees (±0.36 degrees) | ||
| CONTACT TRAVEL POINT DIFFERENCE | Measures "slow-close" contact-point distances; results can be printed | ||
| DISPLAY | Back-lit LCD Screen (20 characters by 4 lines); viewable in bright sunlight and low-light levels | ||
| PRINTER | Built-in 4.5-inch wide thermal printer can print both graphic contact travel waveforms and tabulated test results | ||
| INTERNAL TEST RECORD STORAGE | Stores up to 150 test records | ||
| COMPUTER INTERFACES | One RS-232C port, One USB port | ||
| PC SOFTWARE | Windows® XP/Vista-based Breaker-Analysis software is included with purchase price | ||
| SAFETY | Designed to meet UL 6101A-1 and CAN/CSA C22.2 No 1010.1-92 standards | ||
| ENVIRONMENT | Operating: -10°C to 50°C (+15°F to +122°F); Storage: -30°C to70°C (-22°F to +158°F) | ||
| OPTIONS | Transportation case (available for the CT-7000 S2 and the travel transducers) | ||
| WARRANTY | One year on parts and labor |
CT-7500 S2 - ANALIZADOR DIGITAL DE INTERRUPTOR
El CT-7500 Serie 2 es un Analizador de Interruptores de EAT, de funcionamiento independiente operado por una micro-computadora. Es económico y fácil de utilizar. Tiene dos Modos de operación: el tradicional análisis de Tiempo & Movimiento de contactos o en Prueba Rápida (medición de tiempos en Servicio).
| TYPE | Portable circuit-breaker analyzer | ||
| PHYSICAL SPECIFICATIONS | 16"W X 11"H x 14"D (40.6 cm x 29.9 cm x 35.6 cm); Weight: less than 25 lbs (11.3 kg) | ||
| INPUT POWER | 100 - 120 Vac or 200 - 240 Vac (selectable), 50/60Hz | ||
| DRY CONTACT INPUTS | 3, 6 or 12 dry-input channels (depending on model). Each channel detects main and insertion-resistor contacts | ||
| TIMING WINDOWS | 1-second, 10-seconds, or 20-seconds | ||
| TIMING RESOLUTIONS | ±50 micro-seconds @ 1-second duration, ±500 micro-seconds @ 10-second duration, ±1.0 milli-seconds @ 20-second duration | ||
| TIMING ACCURACY | 0.05% of reading ±0.05 ms @ 1-second duration | ||
| DRY-CONTACT CHANNEL PROTECTION | All contact inputs are grounded until test; input channels are protected against static discharge | ||
| DRY-CONTACT DETECTION RANGE | Closed: less than 20 ohms; Open: greater than 5,000 ohms | ||
| RESISTOR DETECTION RANGE | 50 - 5,000 ohms | ||
| CT CURRENT SENSOR | One, non-contact, 0 - 100 Amperes | ||
| TRIGGER INPUT VOLTAGE | Open/Close: 30 - 300V, DC or peak AC | ||
| VOLTAGE SENSING INPUT RANGE | V1: analog input; 0 - 255V DC or peak AC; Sensitivity ±1V; V2: voltage presence/absence detector input; 30 - 300V DC or peak AC | ||
| BREAKER OPERATIONS | Initiate Open, Close, Open- Close, Close - Open, Open - Close - Open | ||
| BREAKER INITIATE CAPACITY | 30A, 250Vac/dc max | ||
| INITIATE CURRENT READING RANGE | One, non-contact, Hall-effect sensor, 0 - 20 amp range, dc to 5Khz | ||
| TRAVEL TRANSDUCER INPUTS | 3 digital travel transducer channels; Linear range, 0.0 - 60.0 in (±0.01 in); Rotary range: 0 - 360 degrees (±0.36 degrees) | ||
| CONTACT TRAVEL POINT DIFFERENCE | Measures "slow-close" contact-point distances; results can be printed | ||
| DISPLAY | Back-lit LCD Screen (20 characters by 4 lines); viewable in bright sunlight and low-light levels | ||
| PRINTER | Built-in 4.5-inch wide thermal printer can print both graphic contact travel waveforms and tabulated test results | ||
| INTERNAL TEST RECORD STORAGE | Stores up to 150 test records | ||
| COMPUTER INTERFACES | One RS-232C port, One USB port | ||
| PC SOFTWARE | Windows® XP/Vista-based Breaker-Analysis software is included with purchase price | ||
| SAFETY | Designed to meet UL 6101A-1 and CAN/CSA C22.2 No 1010.1-92 standards | ||
| ENVIRONMENT | Operating: -10°C to 50°C (+15°F to +122°F); Storage: -30°C to70°C (-22°F to +158°F) | ||
| OPTIONS | Transportation case (available for the CT-7500 S2 and the travel transducers) | ||
| WARRANTY | One year on parts and labor |
CT-8000 - ANALIZADOR DIGITAL DE INTERRUPTOR
El CT-8000 es un Analizador de Interruptores de EAT de quinta generación. El modelo CT-8000 es un analizador de interruptores independiente y controlado por una micro-computadora. Es económico y fácil de utilizar. Tiene dos modos de operación: el tradicional análisis de tiempo & movimiento de contactos o en prueba rápida (medición de tiempos en servicio). El CT-8000 está disponible con configuraciones de 3 contactos secos (CT-8000-3) o 6 contactos secos (CT-8000-6). Ambos modelos poseen 3 canales digitales para transductores de movimiento.
| TYPE | Portable circuit-breaker analyzer | ||
| PHYSICAL SPECIFICATIONS | 16"W X 11"H x 14"D (40.6 cm x 29.9 cm x 35.6 cm); Weight: less than 25 lbs (11.3 kg) | ||
| INPUT POWER | 100 - 120 Vac or 200 - 240 Vac (selectable), 50/60Hz | ||
| DRY CONTACT INPUTS | 3 or 6 dry-input channels (depending on model). Each channel detects main and insertion-resistor contacts | ||
| TIMING WINDOWS | 1-second, 10-seconds, or 20-seconds | ||
| TIMING RESOLUTIONS | ±50 micro-seconds @ 1-second duration, ±500 micro-seconds @ 10-second duration, ±1.0 milli-seconds @ 20-second duration | ||
| TIMING ACCURACY | 0.05% of reading ±0.05 ms @ 1-second duration | ||
| RESISTOR DETECTION RANGE | 50 - 5,000 ohms | ||
| CT CURRENT SENSOR | One, non-contact, 0 - 100 Amperes | ||
| TRIGGER INPUT VOLTAGE | Open/Close: 30 - 300V, DC or peak AC | ||
| VOLTAGE SENSING INPUT RANGE | V1: analog input; 0 - 255V DC or peak AC; Sensitivity ±1V; V2: voltage presence/absence detector input; 30 - 300V DC or peak AC | ||
| BREAKER OPERATIONS | Initiate Open, Close, Open- Close, Close - Open, Open - Close - Open | ||
| BREAKER INITIATE CAPACITY | 25A, 250Vac/dc max (100A Inrush) | ||
| INITIATE CURRENT READING RANGE | One, non-contact, Hall-effect sensor, 0 - 20 amp range, dc to 5Khz | ||
| TRAVEL TRANSDUCER INPUTS | 3 digital travel transducer channels; Linear range, 0.0 - 60.0 in (±0.01 in); Rotary range: 0 - 360 degrees (±0.36 degrees) | ||
| CONTACT TRAVEL POINT DIFFERENCE | Measures "slow-close" contact-point distances; results can be printed | ||
| DYNAMIC/STATIC RESISTANCE RANGE | 0.1 - 1,999 micro-ohms; Accuracy: ±2% of reading, ±5 micro-ohms | ||
| RESISTANCE TEST CURRENT | 200 Amperes typical | ||
| RESISTOR TYPE TRANSDUCER INPUT | 200 Ohms - 10K Ohms | ||
| DISPLAY | Back-lit LCD Screen (20 characters by 4 lines); viewable in bright sunlight and low-light levels | ||
| PRINTER | Built-in 4.5-inch wide thermal printer can print both graphic contact travel waveforms and tabulated test results | ||
| INTERNAL TEST RECORD STORAGE | Stores up to 150 test records | ||
| COMPUTER INTERFACES | One RS-232C port, One USB port | ||
| PC SOFTWARE | Windows® XP/Vista-based Breaker-Analysis software is included with purchase price | ||
| SAFETY | Designed to meet UL 6101A-1 and CAN/CSA C22.2 No 1010.1-92 standards | ||
| ENVIRONMENT | Operating: -10°C to 50°C (+15°F to +122°F); Storage: -30°C to70°C (-22°F to +158°F) | ||
| OPTIONS | Transportation case (available for the CT-8000 and the travel transducers) | ||
| WARRANTY | One year on parts and labor |
DIGITMR - ANALIZADOR DE INTERRUPTORES EAT
El Digi-TMR de VIC es un Analizador de Interruptores de EAT, de funcionamiento independiente operado por una micro-computadora. Es económico y fácil de utilizar.
| TYPE | Circuit-breaker analyzer | ||
| PHYSICAL SPECIFICATIONS | 18"W x 7"H x 15"D (45.7 cm x 17.8 cm x 38.1 cm); Weight: less than 19 lbs (8.6 kg) | ||
| INPUT POWER | 3 Amps, 100 - 120 Vac or 200 - 240 Vac (factory pre-set), 50/60 Hz | ||
| DRY CONTACT INPUTS | 3 dry-input channels; each channel detects main and insertion-resistor contacts | ||
| TIMING WINDOWS | 1-second, 10-seconds, or 20-seconds | ||
| TIMING RESOLUTIONS | ±100 micro-seconds @ 1-second duration, ±1.00 milli-seconds @ 10-second duration, ±2.00 milli-seconds @ 20-second duration | ||
| TIMING ACCURACY | 0.05% of reading ±0.05 ms @ 1-second duration | ||
| RESISTOR DETECTION RANGE | 50 - 5,000 ohms | ||
| DRY-CONTACT CHANNEL PROTECTION | Fuses protect all isolated power supplies; all contact inputs are grounded until test; input channels are protected against static discharge | ||
| CONTACT DETECTION RANGE | Closed: less than 20 ohms; Open: greater than 5,000 ohms | ||
| RESISTOR DETECTION RANGE | 50 - 5,000 ohms | ||
| TRIGGER INPUT VOLTAGE | Open/Close: 30 - 300V, DC or peak AC | ||
| VOLTAGE SENSING INPUT RANGE | V1: analog input; 0 - 255V DC or peak AC; Sensitivity ±1V; V2: voltage presence/absence detector input; 30 - 300V DC or peak AC | ||
| BREAKER OPERATIONS | Initiate Open, Close, Open- Close, Close - Open, Open - Close - Open | ||
| BREAKER INITIATE CAPACITY | 30A, 250 Vac/dc max | ||
| INITIATE CURRENT READING RANGE | One, non-contact, Hall-effect sensor, 0 - 20 amp range, dc to 5Khz | ||
| TRAVEL TRANSDUCER INPUTS | 1 digital travel transducer channel; Linear range: 0.0 - 60.0 in (±0.005 in.); Rotary range: 0 - 360 degrees (±0.006 degrees) | ||
| CONTACT TRAVEL POINT DIFFERENCE | Measures "slow-close" contact-point distances; results can be printed | ||
| DISPLAY | Back-lit LCD Screen (20 characters by 4 lines); viewable in bright sunlight and low-light levels | ||
| PRINTER | Built-in 4.5-inch wide thermal printer can print both graphic contact travel waveforms and tabulated test results | ||
| INTERNAL TEST RECORD STORAGE | Stores up to 100 test records and 99 breaker test plans | ||
| COMPUTER INTERFACES | One RS-232C port, One USB port | ||
| PC SOFTWARE | Windows® XP/Vista-based Breaker-Analysis software is included with purchase price | ||
| SAFETY | Designed to meet UL 6101A-1 and CAN/CSA C22.2 No 1010.1-92 standards | ||
| ENVIRONMENT | Operating: -10°C to 50°C (+15°F to +122°F); Storage: -30°C to70°C (-22°F to +158°F) | ||
| OPTIONS | Transportation case (available for the DIGITMR and the travel transducers) | ||
| WARRANTY | One year on parts and labor |
MCCB-250 - ANALIZADOR DE INTERRUPTORES DE CAJA MOLDEADA
El MCCB-250 de Vanguard es una fuente de alta corriente programable diseñada específicamente para probar Interruptores de Caja Moldeada, Termo-Magnéticas, Relés de Protección de Sobrecarga de Motores, etc.
| TYPE | 250 Ampere current source | ||
| PHYSICAL SPECIFICATIONS | 16.8"W x 12.6"H x 10.6"D (42.6 cm x 32.0 cm x 27.0 cm); Weight: 46 lbs (21 kg) | ||
| INPUT POWER | 100 - 120 Vac or 200 - 240 Vac (factory pre-set), 50/60 Hz | ||
| OUTPUT CURRENTS | 0 - 5 A @ 120 Vac max; 0 - 25 A @ 24 Vac max; 0 - 120 A @ 6 Vac max; 0 - 250 A @ 3 Vac max | ||
| INTERNAL CURRENT METER | 100 mA - 1000 A; Accuracy: 1% of reading ±20mA | ||
| MEASUREMENT METHOD | Isolated CT | ||
| EXTERNAL METER RANGE | 10 mA - 10 A; Accuracy: 1% of reading, ±2mA | ||
| MEASUREMENT METHOD | Isolated CT | ||
| TIMER READING RANGE | 1ms - 2 hours; Accuracy: 0.1% of reading ±1ms | ||
| TIMER STOP INPUTS | Voltage input (24V - 300V, DC or peak AC), dry contact input, or removal of primary current | ||
| DISPLAY | Back-lit LCD Screen (20 characters by 4 lines); viewable in bright sunlight and low-light levels | ||
| COMPUTER INTERFACE | RS-232C port for factory calibration and diagnostics | ||
| SAFETY | Designed to meet IEC61010 (1995), UL61010A-1, CSA-C22.2 standards | ||
| ENVIRONMENT | Operating: -10ºC to 50º C (15ºF to +122º F); Storage: -30º C to 70º C (-22ºF to +158º F) | ||
| CABLES | Power cord, ground cable, 10-foot #2 AWG test leads | ||
| OPTIONS | Transportation case | ||
| WARRANTY | One year on parts and labor |
RESISTOR TRANSDUCER ADAPTER
The Vanguard Resistor Transducer Adapter (RTA) can be used to connect any resistor type transducer to the digital transducer channel of a Vanguard circuit breaker analyzer. The RTA also features a 3-pin SwitchCraft connector that can directly interface with ABB resistor transducers.
UPS S2 - FUENTE DE ALIMENTACION UNIVERSAL
La Fuente de Alimentación Universal (UPS-S2) de Vanguard está diseñada para cumplir las necesidades de una fuente independiente de tensión de CA/CC. Ambas tensiones AC y CC pueden entregar 10A en forma permanente.
| TYPE | Potable AC/DC power supply | ||
| PHYSICAL SPECIFICATIONS | 21"W x 17"H x 9"D (53 cm x 43 cm x 24 cm); Weight: 55 lbs (25 Kg) | ||
| INPUT POWER | 100 - 120 Vac or 200 - 240 Vac (factory pre-set), 50/60 Hz | ||
| DC OUTPUT VOLTAGE | 10 - 300 Vdc @ 10 amperes | ||
| AC OUTPUT VOLTAGE | 10 - 240 Vac @ 10 amperes | ||
| SAFETY | Designed to meet UL 61010A-1 and CAN/CSA C22.2 No. 1010.1-92 standards | ||
| ENVIRONMENT | Operating: -10° to 50° C (15°F to +122° F); Storage: -30° C to 70° C (-22°F to +158° F) | ||
| CABLES | Power cord, ground cable, 10-foot test leads | ||
| OPTIONS | Transportation case | ||
| WARRANTY | One year on parts and labor |
HOME |
INVESTIGACION|
LOCALIZACION DE FALLAS |
PREGUNTAS FRECUENTES |
ARTICULOS TECNICOS |
CURSOS |
EVENTOS |
CONTACTO
Copyright 2008 - 2012 INDUCOR INGENIERIA S.A. | Todos los derechos reservados | CCS | HTML
Copyright 2008 - 2012 INDUCOR INGENIERIA S.A. | Todos los derechos reservados | CCS | HTML